Flat Conversion Drawings in Feltham TW13
Fixed-fee, MCIAT-chartered flat conversion drawings for Feltham (TW13) homeowners — London Borough of Hounslow validation and local constraints handled from the start.
Feltham is an outer-west Hounslow suburb built largely between the wars and in the post-war decades, so the bulk of our work here is family-driven: single-storey rear extensions, side-return infills and loft conversions on 1930s semis and estate housing. Wide plots on roads such as Southern Avenue and Ashmead Road usually leave comfortable room to extend under permitted development while keeping the front elevation intact.
Where a plot sits near the St Dunstan's or Hanworth Park conservation areas, or on the lower ground close to the River Crane, we design to Hounslow Council's expectations from the outset — matching brick and roof lines, respecting the depth and height limits, and building in flood-resilient drainage detail so the application clears validation without an avoidable refusal.
Planning in Feltham (TW13): what to know before you apply
There is no published householder Article 4 direction in Feltham, so most rear and loft projects proceed under permitted development. Watch the St Dunstan's, Hanworth Park and Feltham Town Centre conservation areas, and the flood constraint on plots near the River Crane, where PD rights and extension depths are more tightly read.
Typical Feltham housing stock
Feltham is dominated by 1930s bay-fronted semis and post-war council-built estates, with generous rear gardens on roads like Southern Avenue and Glebelands Road. Plots are wide enough for single-storey rear extensions, side infills and hip-to-gable loft conversions without needing to touch the front elevation.
Streets we regularly draw for in Feltham
Southern Avenue · Glebelands Road · Ashmead Road · Browells Lane
What TW13 is actually built of
Measured from 396 classified residential buildings in TW13, not from a description of the area.
Feltham TW13 housing mix
Residential building form across the TW13 postcode district, from 396 classified buildings.
| Attached on more than one side | 41% |
|---|---|
| Attached on one side | 54% |
| Detached | 5% |
| Median building footprint | 54 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.56 |
| Buildings classified | 396 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Flat Conversion Drawings for Feltham (TW13) homes: the package and the process
Converting a house into flats is drawn unit by unit. Each proposed flat needs its layout, its floor area, its own entrance arrangement and its amenity provision shown, along with refuse and cycle storage that meets the standards the council applies to new residential units.
The separation between units is the technical core: floors and walls detailed for fire resistance and sound insulation, a common escape route drawn and protected, and services routed without breaching the compartments. Those details go on the drawings because Building Control assesses them there, not on site.
Conversion suits buildings with the plan depth and stair position to make two workable units. A wide terrace or a large semi can usually be split without landlocking a room, while a narrow plan often cannot give both units light, access and separation at the same time.
Do I need planning permission to convert a house into flats?
Yes, always. Converting a single dwelling into two or more self-contained flats is a change from one home to several, and that subdivision is treated as development requiring a full planning application — there is no permitted development route that allows it, regardless of the property's size or whether the exterior changes at all. The application has to demonstrate that each flat meets space, layout, amenity and parking standards in its own right, not just that the building as a whole is being used sensibly.
Boroughs also weigh the loss of a family-sized house against their local housing policy, since converting a larger house into several flats reduces the stock of homes suited to families even as it adds smaller units. We take that policy context into account when advising on layout and unit numbers, rather than simply maximising the number of flats the floor area could technically support.
What sound insulation is required between flats?
Part E of the building regulations sets minimum sound insulation standards for the walls and floors separating flats, covering both airborne and impact sound. Where an existing house is subdivided, the drawings specify how the party floors and walls between units will be upgraded — additional layers, resilient bars, or a floating floor — and pre-completion sound testing is normally required before the flats can be signed off. Getting this detail right on the drawings from the outset matters, because retrofitting sound insulation after a failed test usually means taking up a finished floor or ceiling that has already been decorated.
How do you design fire escape and compartmentation for flat conversions?
Each flat needs its own independent means of escape to a place of safety, and the building has to be compartmented so that fire in one flat does not spread into another or into the shared circulation space. On a typical converted house this means fire-rated floors, walls and doors between units, and either a protected common stairway shared by the flats or separate final exits for each one, depending on the layout.
Where flats sit above ground floor level, escape routes and fire doors are designed together with the sound insulation upgrade, since the same floor and wall build-ups often need to satisfy both requirements at once.
| Conversion | Typical scope | Route | Fee from |
|---|---|---|---|
| House to two self-contained flats | Vertical split, separate or shared entrance | Full planning plus building regulations | £1,600 |
| House to three or more flats | Multiple units, fire strategy required | Full planning plus building regs plus structural | £2,400 |
| Flat conversion with a side or rear extension | Additional floor area added to create compliant units | Full planning plus structural calculations | £2,800 |
Flat Conversion Drawings in Feltham TW13 — FAQs
Do I need planning permission to convert a house into flats?+
How much do flat conversion drawings cost in London?+
What sound insulation is required between flats?+
Does each flat need a separate fire escape?+
What is the minimum size for a flat in London?+
Do I need planning permission for an extension in Hounslow?+
What extra control applies in Bedford Park?+
Does Heathrow or the river affect my Hounslow project?+
How long does Hounslow Council take to decide?+
How much do planning drawings cost in Hounslow?+
Get your free Feltham planning assessment
Tell us your Feltham (TW13) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.