Single-storey rear extension onto a garden behind an interwar Becontree RM9 LCC cottage in Barking and Dagenham

Becontree · RM9 · Barking & Dagenham

Hip-to-Gable Loft Conversion Drawings in Becontree RM9

Fixed-fee, MCIAT-chartered hip-to-gable loft conversion drawings for Becontree (RM9) homeowners — London Borough of Barking and Dagenham validation and local constraints handled from the start.

Becontree (RM9) is defined by one thing above all: the Becontree Estate, built by the London County Council between 1921 and 1935 and still one of the largest public housing estates ever created, with roughly 26,000 homes laid out on garden-suburb principles. Almost every householder project here is an extension or loft on one of those cohesive interwar two-storey cottages, so the drawings have to sit comfortably within a very consistent, planned streetscape.

There is no conservation area covering Becontree — that is a genuine, verified fact, not an omission. Its planning character is instead shaped by the sheer uniformity of the estate layout and by the London Borough of Barking and Dagenham's design expectations, which lean on keeping the original cottage rhythm, materials and building lines intact. We treat that estate cohesion, rather than a conservation designation, as the reference point when we design an extension.

Because so many Becontree houses passed into private ownership after Right to Buy, demand for rear extensions, side infills and loft conversions is steady across streets like Gale Street, Lodge Avenue and Fitzstephen Road. We check each property's permitted-development position against Barking and Dagenham's borough-wide controls first, then prepare drawings that either stay within permitted development or are ready to validate as a full householder application.

Proposed floor plan

Becontree RM9

Becontree (RM9) — planning at a glance

Council: London Borough of Barking and Dagenham
Postcode district: RM9
Planning portal: View the Barking & Dagenham planning portal
Housing stock: Two-storey interwar cottages — short terraced and semi-detached runs of brick and rendered houses set behind small front gardens on wide, uniformly planned streets. Built by the London County Council between 1921 and 1935, many are now privately owned following Right to Buy, which is what drives the steady flow of rear-extension and loft-conversion work across the estate.
Article 4: No area-specific Article 4 direction is published for the Becontree Estate; Barking and Dagenham's borough-wide permitted-development controls and the council's householder design guidance still apply.
Sample streets: Lodge Avenue · Gale Street · Marlborough Road · Fitzstephen Road · Ilchester Road · Rutland Gardens · Babington Road · Dronfield Gardens · Hewett Road · Cornworthy Road · Harrold Road · Easebourne Road
Local constraints: Strong estate-wide visual cohesion: the uniform interwar cottage layout means front-elevation changes, roof forms and materials are assessed against a consistent street rhythm rather than a one-off houseBarking and Dagenham's borough-wide permitted-development limits and householder design guidance govern extension depth, height and coverage — no local Article 4 direction narrows them further on the estateMatching original facing brick, render finishes and roof tiles so a rear or side addition reads as part of the original cottage rather than an obvious bolt-onModest original plot and garden sizes on many terraced runs, which constrain how deep a single-storey rear extension can go before it needs a full householder applicationSemi-detached and short-terrace forms where side and rear building lines are shared with neighbours, making party-wall relationships and overshadowing relevant to what gets approved

Planning in Becontree (RM9): what to know before you apply

Because the estate is so uniform, Barking and Dagenham assess extensions on Becontree cottages against the consistent interwar street pattern, so matching original brick, render and roof form matters more than on a mixed-typology road. There is no conservation area and no estate-specific Article 4 direction, so many houses retain permitted development rights for rear and loft work — but the modest original plots and shared building lines mean depth, height and neighbour impact are the points a householder application is judged on.

Typical Becontree housing stock

Two-storey interwar cottages — short terraced and semi-detached runs of brick and rendered houses set behind small front gardens on wide, uniformly planned streets. Built by the London County Council between 1921 and 1935, many are now privately owned following Right to Buy, which is what drives the steady flow of rear-extension and loft-conversion work across the estate.

Streets we regularly draw for in Becontree

Lodge Avenue · Gale Street · Marlborough Road · Fitzstephen Road · Ilchester Road · Rutland Gardens · Babington Road · Dronfield Gardens · Hewett Road · Cornworthy Road · Harrold Road · Easebourne Road

What RM9 is actually built of

Measured from 248 classified residential buildings in RM9, not from a description of the area.

Becontree RM9 housing mix

Residential building form across the RM9 postcode district, from 248 classified buildings.

Attached on more than one side	62%
Attached on one side	37%
Detached	1%
Median building footprint	48 m²
Addresses per buildingAbove about 2 means flats and maisonettes dominate	1.06
Buildings classified	248

Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.

Hip-to-Gable Loft Conversion Drawings for Becontree (RM9) homes: the package and the process

The hip-to-gable case is made on the end elevation. The drawings show the existing hipped roof and the proposed gable side by side at the same scale, with the new brickwork or tile hanging set out, the ridge extended to its new length, and the junction with any neighbouring roof made explicit.

Because the work changes the roof at the boundary, the section and the end elevation also have to show the party wall line and how the new gable is built off it. Where the property is one of a pair, we draw the neighbouring roof too — an officer assessing the effect on the pair needs to see both.

The conversion needs a hip to work on, which limits it to semi-detached, detached and end-of-terrace houses — a mid-terrace has no hipped end to rebuild. On a semi, the new gable also has to be drawn against the neighbour's roof, since the pair was designed to read as one.

What is a hip-to-gable loft conversion?

A hipped roof slopes inward on all sides, including the end wall, rather than finishing in a flat vertical gable. A hip-to-gable conversion rebuilds that sloping hip as a vertical wall, in line with the existing side elevation below, squaring off the roof shape and creating a much larger, more usable loft footprint along that side without altering the rear or front roof slopes at all. It is one of the more straightforward roof alterations to build, because the new gable wall follows the line of the existing external wall rather than introducing a new roof form, which keeps both the design and the construction relatively contained compared with a full mansard rebuild.

Suits semi-detached and end-of-terrace houses with a hipped roof on the side elevation
Squares off the roof by rebuilding the sloping hip as a vertical gable wall
Leaves the front and rear roof slopes untouched

Is a hip-to-gable loft conversion permitted development?

Often, yes. For semi-detached and detached houses, permitted development rules allow more than one hip to be converted to a gable, provided the new roof does not exceed the height of the existing ridge and the total additional volume stays within the usual allowance — 50 cubic metres for detached and semi-detached homes. The new gable wall and roof materials should match the existing building, and the rules tighten or disappear entirely inside a conservation area or under an Article 4 direction, both of which we check before recommending the route. Where a previous owner has already extended into the roof or added a large outbuilding, the remaining volume allowance can be smaller than expected, so we always confirm the running total against your specific property rather than assuming the full allowance is still available.

What is a hip-to-gable-plus-dormer conversion?

Combining a hip-to-gable conversion with a rear dormer is one of the most effective ways to maximise a loft on a semi-detached or end-of-terrace house: the gable squares off the side of the roof while the dormer adds headroom over the rear slope and stairwell, together often creating close to a full-width habitable floor. We assess both elements together from the first survey — see our dormer loft conversion page for how the rear element is designed — rather than drawing a hip-to-gable in isolation and bolting on a dormer later. Because both elements are often permitted development on their own, the combined scheme frequently still fits within the same volume allowance, though we always check the running total before confirming the route.

Typical hip-to-gable loft conversion drawing packages
Conversion	Typical route	Structural scope	Fee from
Hip-to-gable only	Permitted development / LDC	New gable wall and rafter tie-in	£1,300
Hip-to-gable plus rear dormer	Permitted development / LDC where eligible	Gable wall plus dormer structure	£1,450
Hip-to-gable in a conservation area	Householder planning	New gable wall and rafter tie-in	£1,600

Sheet from a hip-to-gable loft conversion drawings package drawn for a Becontree property in RM9, showing the existing and proposed arrangement at scale — A sheet from the hip-to-gable loft conversion drawings package we submit to London Borough of Barking and Dagenham for Becontree (RM9) properties.

Also in Becontree RM9

Planning Permission Planning Drawings Architectural Drawings Building Regulations Drawings Loft Conversion Drawings Hip-to-Gable Loft Conversion Drawings across Barking & Dagenham Hip-to-Gable Loft Conversion Drawings across London

FAQ

Hip-to-Gable Loft Conversion Drawings in Becontree RM9 — FAQs

How much do hip-to-gable loft conversion drawings cost in London?+

A hip-to-gable conversion on its own typically starts around £1,300. Combining it with a rear dormer usually costs a little more, around £1,450, to cover the additional structural design — we confirm the fixed fee once we have surveyed your roof.

Will my semi-detached house qualify for permitted development?+

Often, but it depends on the volume already used, whether the property sits in a conservation area or under an Article 4 direction, and whether previous extensions have already used up the allowance. We check this free before recommending a route.

How long do hip-to-gable drawings take?+

Typically around 7 days from survey to a full drawing set in your online portal, whether the route is a Lawful Development Certificate or full planning.

Do I need an architect for a hip-to-gable conversion?+

No — as MCIAT-chartered architectural technologists we produce the same council-accepted drawings, with structural calculations coordinated in-house, typically at a lower fee than an architecture practice.

What building regulations apply to a hip-to-gable loft?+

The same core requirements as any loft conversion: a protected stairway or upgraded fire doors, a compliant means-of-escape window, structural calculations for the new gable wall and floor, and insulation upgraded to current Part L standards. We coordinate all of this alongside the planning or Lawful Development Certificate drawings.

Do I need planning permission to extend a house on the Becontree Estate?+

Not always. Many Becontree cottages retain permitted development rights, so a modest single-storey rear extension or a rear loft conversion can often proceed without a full planning application. Because the original plots are compact and the estate is uniform, we check your property's size limits and building lines against Barking and Dagenham's controls first, and prepare a full householder application where the project goes beyond permitted development.

Is Becontree in a conservation area?+

No. There is no conservation area covering the Becontree Estate. Its planning character is shaped instead by the estate's uniform interwar cottage layout and Barking and Dagenham's householder design expectations, which favour keeping the original street rhythm, materials and roof form intact when you extend.

How much do planning and building-regulation drawings cost for a Becontree extension?+

We work to fixed fees agreed before we start, with a typical turnaround of around seven days for a standard rear extension or loft on a Becontree cottage. As a chartered architectural technologist practice we produce the same council-accepted planning and building-regulation drawings as an architect, usually for a lower fee, and include free redraws until your application is approved.

How long does Barking & Dagenham Council take to decide?+

The council determines most householder applications within the statutory eight-week period once validated; conservation cases can attract additional consultation. The commonest delay is a validation query, so we prepare submissions to the council's checklist with correctly scaled existing and proposed drawings and a location plan.

Free Fixed Quote

Get your free Becontree planning assessment

Tell us your Becontree (RM9) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.