Planning Permission in Thames View IG11
Fixed-fee, MCIAT-chartered planning permission for Thames View (IG11) homeowners — London Borough of Barking and Dagenham validation and local constraints handled from the start.
Thames View (IG11) is a cohesive 1950s London County Council overspill estate, built on former marshland south of Barking town centre as a planned postwar community of low-rise council-built houses and blocks. That open, uniform estate layout — quite distinct from the borough's older terraced streets — is what shapes nearly every householder project here, so an extension has to sit comfortably within a very consistent, planned streetscape.
There is no conservation area covering Thames View — that is a genuine, verified fact, not an omission. Its planning character is shaped instead by the sheer uniformity of the estate layout and by Barking and Dagenham's householder design expectations, which lean on keeping the original postwar rhythm, materials and building lines intact. We treat that estate cohesion, rather than a conservation designation, as the reference point when we design an extension.
Because so many Thames View houses passed into private ownership after Right to Buy, demand for rear extensions, side infills and loft conversions is steady across streets like Bastable Avenue, Maplestead Road and Moore Crescent. We check each property's permitted-development position against Barking and Dagenham's borough-wide controls first, then prepare drawings that either stay within permitted development or are ready to validate as a full householder application.
Planning in Thames View (IG11): what to know before you apply
Because the estate is so uniform, Barking and Dagenham assess extensions on Thames View houses against the consistent postwar street pattern, so matching brick, render and roof form matters more than on a mixed-typology road. There is no conservation area and no estate-specific Article 4 direction, so many houses retain permitted development rights for rear and loft work — but the open estate layout, shared building lines and low-lying former-marshland ground mean spacing, neighbour impact and drainage are the points an application turns on.
Typical Thames View housing stock
Cohesive 1950s council-built houses and low-rise blocks arranged on a planned, open postwar layout, many now privately owned following Right to Buy — which is what drives the steady flow of rear-extension and loft-conversion work across the estate.
Streets we regularly draw for in Thames View
Bastable Avenue · River Road · Renwick Road · Choats Road · Upney Lane · Stamford Road · Aconbury Road · Pinley Gardens · Burnham Road · Maplestead Road · Castle Road · Moore Crescent
What IG11 is actually built of
Measured from 261 classified residential buildings in IG11, not from a description of the area.
Thames View IG11 housing mix
Residential building form across the IG11 postcode district, from 261 classified buildings.
| Attached on more than one side | 60% |
|---|---|
| Attached on one side | 38% |
| Detached | 2% |
| Median building footprint | 59 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.92 |
| Buildings classified | 261 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Planning Permission for Thames View (IG11) homes: the package and the process
A householder application is refused validation far more often than it is refused permission, and almost always for the same reasons: a location plan at the wrong scale, no red line around the application site, a missing ownership certificate, or elevations that do not show every face of the building affected. We prepare the full submission set — location plan, block plan, existing and proposed floor plans, elevations and sections — so the case officer receives a complete case on day one.
Once the application is live we stay on it. Officers routinely come back with questions about materials, boundary treatment or a dimension they cannot read off the drawings, and a fast, drawn answer is usually the difference between a decision inside the statutory period and a request to withdraw and resubmit.
Which route applies is decided by the building before it is decided by policy. A house that has never been extended usually has allowances left to use; a flat, a listed building or a home in a conservation area often has none, and the same drawing set then has to make a design case rather than a compliance one.
Do I need planning permission for an extension in London?
Many single-storey rear extensions, loft conversions and outbuildings fall under permitted development rights and do not need a full planning application — but London's dense housing stock, conservation areas and Article 4 directions frequently withdraw those rights. Before you pay for a full application, we check your property against the current permitted development thresholds and your borough's local constraints.
Where permitted development applies, we recommend a Lawful Development Certificate instead of full planning — it is faster, cheaper and gives you a legal document confirming the work was lawful. Where a full application is genuinely required, we prepare it properly the first time.
Permitted development vs a full planning application
Permitted development lets you build within defined volumetric limits without committee review. A full householder application is assessed against the borough's local plan for scale, daylight, neighbour impact and design. We advise which route your project qualifies for and why.
Article 4 directions and conservation areas
If your home sits in a conservation area or under an Article 4 direction, permitted development rights are often removed — meaning even modest changes need consent. Each borough page lists the local directions and conservation areas we routinely design around.
How do you apply for planning permission through the London Planning Portal?
We manage the full lifecycle of your submission — survey, drawings, supporting documents and officer liaison — so you never have to decode a validation checklist yourself.
Phase 1 — existing and proposed site surveys
A laser-measured survey captures your property exactly, so existing and proposed drawings match reality millimetre for millimetre.
Phase 2 — technical drawing package
Site location plan, block plan, floor plans, elevations and sections drawn to your borough's scale and formatting requirements, with a design and access statement where needed.
Phase 3 — liaison with the planning officer
We answer the council's queries, negotiate amendments, and redraw free until the decision lands.
How long does planning permission take, and what does it cost?
Drawings are typically ready within 7 days of survey. Your council then has a statutory 8 weeks to decide a householder application. Our drawing fees are fixed and quoted upfront — the table below shows typical packages.
| Package | Production window | Compliance layer | Typical fee |
|---|---|---|---|
| Permitted Development pack | 7–10 working days | Lawful Development Certificate submission | £950–£1,450 |
| Full Planning pack | 10–14 working days | Council liaison & design statement | £1,600–£2,400 |
| Planning + Building Regs pack | 14–21 working days | Structural calculations included | £2,200–£3,850 |
Planning Permission in Thames View IG11 — FAQs
How long does it take to get planning permission from a London council?+
What happens if the council refuses?+
Do you cover my borough?+
Is the fee really fixed?+
Do I need planning permission to extend a house in Thames View?+
Is Thames View in a conservation area?+
How much do planning and building-regulation drawings cost for a Thames View extension?+
How long does Barking & Dagenham Council take to decide?+
Get your free Thames View planning assessment
Tell us your Thames View (IG11) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.