Hip-to-Gable Loft Conversion Drawings in Barnes SW13
Fixed-fee, MCIAT-chartered hip-to-gable loft conversion drawings for Barnes (SW13) homeowners — London Borough of Richmond upon Thames validation and local constraints handled from the start.
Barnes (SW13) is an unusually intact riverside village in Richmond, and it is heavily conservation-controlled: four conservation areas — Barnes Common, Barnes Green, Castelnau and Madrid Road — cover most of the housing. Whether a property sits inside one of those boundaries, and often it does, is the single biggest factor in how an extension, loft or elevation change is designed and assessed.
The Thames wraps the neighbourhood on two sides, so riverside houses along Lonsdale Road and the Terrace also carry flood-zone considerations, and Barnes Common is protected metropolitan open land. We map a Barnes property against the conservation, flood-zone and open-land boundaries first, then design the drawings to Richmond's residential and conservation guidance so the application is validated without a query.
Planning in Barnes (SW13): what to know before you apply
SW13 has no householder Article 4 direction, but its four conservation areas mean permitted development cannot be assumed across most of Barnes, and riverside properties along Lonsdale Road sit within the Thames flood zone — both are checked before we recommend a route.
Typical Barnes housing stock
Victorian and Edwardian terraces and cottages around Barnes Green and the village, the grand Italianate semi-detached villas along Castelnau toward Hammersmith Bridge, and riverside houses fronting the Thames on Lonsdale Road.
Streets we regularly draw for in Barnes
Church Road · Castelnau · White Hart Lane · Lonsdale Road
What SW13 is actually built of
Measured from 328 classified residential buildings in SW13, not from a description of the area.
Barnes SW13 housing mix
Residential building form across the SW13 postcode district, from 328 classified buildings.
| Attached on more than one side | 48% |
|---|---|
| Attached on one side | 47% |
| Detached | 5% |
| Median building footprint | 75 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.29 |
| Buildings classified | 328 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Hip-to-Gable Loft Conversion Drawings for Barnes (SW13) homes: the package and the process
The hip-to-gable case is made on the end elevation. The drawings show the existing hipped roof and the proposed gable side by side at the same scale, with the new brickwork or tile hanging set out, the ridge extended to its new length, and the junction with any neighbouring roof made explicit.
Because the work changes the roof at the boundary, the section and the end elevation also have to show the party wall line and how the new gable is built off it. Where the property is one of a pair, we draw the neighbouring roof too — an officer assessing the effect on the pair needs to see both.
The conversion needs a hip to work on, which limits it to semi-detached, detached and end-of-terrace houses — a mid-terrace has no hipped end to rebuild. On a semi, the new gable also has to be drawn against the neighbour's roof, since the pair was designed to read as one.
What is a hip-to-gable loft conversion?
A hipped roof slopes inward on all sides, including the end wall, rather than finishing in a flat vertical gable. A hip-to-gable conversion rebuilds that sloping hip as a vertical wall, in line with the existing side elevation below, squaring off the roof shape and creating a much larger, more usable loft footprint along that side without altering the rear or front roof slopes at all. It is one of the more straightforward roof alterations to build, because the new gable wall follows the line of the existing external wall rather than introducing a new roof form, which keeps both the design and the construction relatively contained compared with a full mansard rebuild.
- Suits semi-detached and end-of-terrace houses with a hipped roof on the side elevation
- Squares off the roof by rebuilding the sloping hip as a vertical gable wall
- Leaves the front and rear roof slopes untouched
Is a hip-to-gable loft conversion permitted development?
Often, yes. For semi-detached and detached houses, permitted development rules allow more than one hip to be converted to a gable, provided the new roof does not exceed the height of the existing ridge and the total additional volume stays within the usual allowance — 50 cubic metres for detached and semi-detached homes. The new gable wall and roof materials should match the existing building, and the rules tighten or disappear entirely inside a conservation area or under an Article 4 direction, both of which we check before recommending the route. Where a previous owner has already extended into the roof or added a large outbuilding, the remaining volume allowance can be smaller than expected, so we always confirm the running total against your specific property rather than assuming the full allowance is still available.
What is a hip-to-gable-plus-dormer conversion?
Combining a hip-to-gable conversion with a rear dormer is one of the most effective ways to maximise a loft on a semi-detached or end-of-terrace house: the gable squares off the side of the roof while the dormer adds headroom over the rear slope and stairwell, together often creating close to a full-width habitable floor. We assess both elements together from the first survey — see our dormer loft conversion page for how the rear element is designed — rather than drawing a hip-to-gable in isolation and bolting on a dormer later. Because both elements are often permitted development on their own, the combined scheme frequently still fits within the same volume allowance, though we always check the running total before confirming the route.
| Conversion | Typical route | Structural scope | Fee from |
|---|---|---|---|
| Hip-to-gable only | Permitted development / LDC | New gable wall and rafter tie-in | £1,300 |
| Hip-to-gable plus rear dormer | Permitted development / LDC where eligible | Gable wall plus dormer structure | £1,450 |
| Hip-to-gable in a conservation area | Householder planning | New gable wall and rafter tie-in | £1,600 |
Hip-to-Gable Loft Conversion Drawings in Barnes SW13 — FAQs
How much do hip-to-gable loft conversion drawings cost in London?+
Will my semi-detached house qualify for permitted development?+
How long do hip-to-gable drawings take?+
Do I need an architect for a hip-to-gable conversion?+
What building regulations apply to a hip-to-gable loft?+
Do I need planning permission for an extension in Richmond?+
My Richmond home is near the river — does flood risk affect my application?+
What does Richmond's Article 4 coverage mean in practice?+
How long does Richmond Council take to decide?+
How much do planning drawings cost in Richmond?+
Get your free Barnes planning assessment
Tell us your Barnes (SW13) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.