Structural Drawings in Thames View IG11
Fixed-fee, MCIAT-chartered structural drawings for Thames View (IG11) homeowners — London Borough of Barking and Dagenham validation and local constraints handled from the start.
Thames View (IG11) is a cohesive 1950s London County Council overspill estate, built on former marshland south of Barking town centre as a planned postwar community of low-rise council-built houses and blocks. That open, uniform estate layout — quite distinct from the borough's older terraced streets — is what shapes nearly every householder project here, so an extension has to sit comfortably within a very consistent, planned streetscape.
There is no conservation area covering Thames View — that is a genuine, verified fact, not an omission. Its planning character is shaped instead by the sheer uniformity of the estate layout and by Barking and Dagenham's householder design expectations, which lean on keeping the original postwar rhythm, materials and building lines intact. We treat that estate cohesion, rather than a conservation designation, as the reference point when we design an extension.
Because so many Thames View houses passed into private ownership after Right to Buy, demand for rear extensions, side infills and loft conversions is steady across streets like Bastable Avenue, Maplestead Road and Moore Crescent. We check each property's permitted-development position against Barking and Dagenham's borough-wide controls first, then prepare drawings that either stay within permitted development or are ready to validate as a full householder application.
Planning in Thames View (IG11): what to know before you apply
Because the estate is so uniform, Barking and Dagenham assess extensions on Thames View houses against the consistent postwar street pattern, so matching brick, render and roof form matters more than on a mixed-typology road. There is no conservation area and no estate-specific Article 4 direction, so many houses retain permitted development rights for rear and loft work — but the open estate layout, shared building lines and low-lying former-marshland ground mean spacing, neighbour impact and drainage are the points an application turns on.
Typical Thames View housing stock
Cohesive 1950s council-built houses and low-rise blocks arranged on a planned, open postwar layout, many now privately owned following Right to Buy — which is what drives the steady flow of rear-extension and loft-conversion work across the estate.
Streets we regularly draw for in Thames View
Bastable Avenue · River Road · Renwick Road · Choats Road · Upney Lane · Stamford Road · Aconbury Road · Pinley Gardens · Burnham Road · Maplestead Road · Castle Road · Moore Crescent
What IG11 is actually built of
Measured from 261 classified residential buildings in IG11, not from a description of the area.
Thames View IG11 housing mix
Residential building form across the IG11 postcode district, from 261 classified buildings.
| Attached on more than one side | 60% |
|---|---|
| Attached on one side | 38% |
| Detached | 2% |
| Median building footprint | 59 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.92 |
| Buildings classified | 261 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Structural Drawings for Thames View (IG11) homes: the package and the process
Structural sheets are issued to be built from. Beam and lintel schedules give size, grade and bearing; connection details show how each element meets the next; and padstones, straps and restraint are drawn at the junctions rather than noted in general terms. Calculations are submitted alongside so Building Control can check the design rather than take it on trust.
Coordination with the architectural set is where the value is. A beam that is right in isolation but sits below the approved ceiling line, or a column that lands in a doorway, is a site problem that costs more to fix than it did to draw. We resolve those clashes in the drawing stage.
The existing structure sets the design. A terrace transfers load through party walls that are shared and often unrecorded, a semi through one; and floor construction — timber, concrete, or a mix from earlier alterations — changes how a new opening is supported and what has to be exposed to find out.
Do I need structural calculations to remove a load-bearing wall in London?
If a wall carries any load from above — a floor, a roof, another wall, or a chimney breast — you need a structural calculation before it can be removed, and Building Control will ask for it as part of a Full Plans or Building Notice submission. This covers the great majority of kitchen-diner knock-throughs in London terraces and semis, where the wall between the kitchen and the rear reception room is almost always load-bearing. A calculation confirms the size and type of steel beam needed to replace the wall's support, the padstones or pier that carry the beam's weight down to the foundations, and the temporary propping needed while the work is carried out. If the wall shares a boundary or the new beam bears on a party wall, the Party Wall etc. Act 1996 will also apply and needs to be dealt with separately from the calculation itself.
How steel beam sizing works
A structural engineer calculates the loads bearing down on a wall from the floors, roof and any walls above it, then sizes a steel beam (RSJ) — its depth, width and steel grade — so it can safely carry that load across the required span without excessive deflection. The calculation also fixes the bearing length at each end, the padstones or steel plates that spread the load into the surrounding masonry, and whether the existing foundations need strengthening to take the extra point loads. Because we coordinate the calculation with the architectural drawing set, the exact beam size, orientation and position shown on your plans is the one the calculation specifies — so your builder can order the correct steel first time, and Building Control sees a consistent set of drawings rather than two documents that disagree.
How much do structural drawings cost in London?
Structural drawings and calculations start from £650 for a single beam or wall removal, agreed as a fixed fee before work begins. The price depends on the number of beams or walls involved, whether foundations need designing from scratch (as with a rear or side extension), whether existing floor and roof structures need checking for extra loading (as with most loft conversions), and whether retaining or underpinning calculations are required, as they are for basement conversions. Where structural work is part of a wider extension, loft or basement project, the structural calculation is typically bundled into the overall building regulations fee rather than charged again separately.
| Project scope | What's included | Fee guide |
|---|---|---|
| Single beam or wall removal | One steel calculation plus a drawing showing beam size, padstones and bearings | From £650 |
| Loft conversion structural package | Floor and roof loading checks, beam calculations, staircase opening design | Included within loft drawings from £1,100 |
| Rear or side extension structural package | Foundation design, steel beam calculations, roof loading checks | Included within planning and building regs packages from £2,200–£3,850 |
| Basement or retaining structure | Underpinning, retaining wall and waterproofing-adjacent structural calculations | Quoted individually — ground conditions vary |
Structural Drawings in Thames View IG11 — FAQs
Do I need a structural engineer to remove a wall in my London home?+
How long do structural calculations take?+
Will the steel beam on my drawings match what my builder orders?+
Can you produce structural drawings without handling my full planning application?+
Do structural calculations need to be submitted to Building Control?+
Do I need planning permission to extend a house in Thames View?+
Is Thames View in a conservation area?+
How much do planning and building-regulation drawings cost for a Thames View extension?+
How long does Barking & Dagenham Council take to decide?+
Get your free Thames View planning assessment
Tell us your Thames View (IG11) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.