Structural Drawings in Bexley Village DA5
Fixed-fee, MCIAT-chartered structural drawings for Bexley Village (DA5) homeowners — London Borough of Bexley validation and local constraints handled from the start.
Bexley Village (DA5) sits on the River Cray at the south-eastern edge of the borough, where the historic High Street winds down past cottages and shops to the green and St John's Church. Rear and side extensions on the Victorian and Edwardian houses ringing the old core are the most common projects here, and the village's semi-rural setting on the edge of the Metropolitan Green Belt shapes how the council reads them.
The Old Bexley Conservation Area, first designated in 1971 and extended in 1987, covers the winding High Street, the green and the riverside around the old ford, protecting 18 listed buildings and the prevailing local brick. Where a DA5 property sits relative to that boundary decides whether roofline, window and front-elevation changes are permitted development or need consent.
Planning in Bexley Village (DA5): what to know before you apply
Inside the Old Bexley Conservation Area the Article 4(2) Direction means front-elevation, roof, window and boundary changes that would be permitted development elsewhere need a full householder application, and the 18 listed buildings additionally require listed-building consent. Beyond the boundary, on the Edwardian and inter-war streets toward the station, many rear and loft projects still fall within permitted development, so we check the boundary and the Green Belt edge before advising a route.
Typical Bexley Village housing stock
The conservation-area core is a tight grain of 18th- and 19th-century brick cottages, listed timber-framed houses and Victorian shopfronts along the winding High Street, giving way to Edwardian villas and inter-war semis on the rising ground toward Bexley station and Parkhill Road.
Streets we regularly draw for in Bexley Village
High Street · Tanyard Lane · Manor Road · North Cray Road
What DA5 is actually built of
Measured from 275 classified residential buildings in DA5, not from a description of the area.
Bexley Village DA5 housing mix
Residential building form across the DA5 postcode district, from 275 classified buildings.
| Attached on more than one side | 28% |
|---|---|
| Attached on one side | 48% |
| Detached | 25% |
| Median building footprint | 84 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.08 |
| Buildings classified | 275 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Structural Drawings for Bexley Village (DA5) homes: the package and the process
Structural sheets are issued to be built from. Beam and lintel schedules give size, grade and bearing; connection details show how each element meets the next; and padstones, straps and restraint are drawn at the junctions rather than noted in general terms. Calculations are submitted alongside so Building Control can check the design rather than take it on trust.
Coordination with the architectural set is where the value is. A beam that is right in isolation but sits below the approved ceiling line, or a column that lands in a doorway, is a site problem that costs more to fix than it did to draw. We resolve those clashes in the drawing stage.
The existing structure sets the design. A terrace transfers load through party walls that are shared and often unrecorded, a semi through one; and floor construction — timber, concrete, or a mix from earlier alterations — changes how a new opening is supported and what has to be exposed to find out.
Do I need structural calculations to remove a load-bearing wall in London?
If a wall carries any load from above — a floor, a roof, another wall, or a chimney breast — you need a structural calculation before it can be removed, and Building Control will ask for it as part of a Full Plans or Building Notice submission. This covers the great majority of kitchen-diner knock-throughs in London terraces and semis, where the wall between the kitchen and the rear reception room is almost always load-bearing. A calculation confirms the size and type of steel beam needed to replace the wall's support, the padstones or pier that carry the beam's weight down to the foundations, and the temporary propping needed while the work is carried out. If the wall shares a boundary or the new beam bears on a party wall, the Party Wall etc. Act 1996 will also apply and needs to be dealt with separately from the calculation itself.
How steel beam sizing works
A structural engineer calculates the loads bearing down on a wall from the floors, roof and any walls above it, then sizes a steel beam (RSJ) — its depth, width and steel grade — so it can safely carry that load across the required span without excessive deflection. The calculation also fixes the bearing length at each end, the padstones or steel plates that spread the load into the surrounding masonry, and whether the existing foundations need strengthening to take the extra point loads. Because we coordinate the calculation with the architectural drawing set, the exact beam size, orientation and position shown on your plans is the one the calculation specifies — so your builder can order the correct steel first time, and Building Control sees a consistent set of drawings rather than two documents that disagree.
How much do structural drawings cost in London?
Structural drawings and calculations start from £650 for a single beam or wall removal, agreed as a fixed fee before work begins. The price depends on the number of beams or walls involved, whether foundations need designing from scratch (as with a rear or side extension), whether existing floor and roof structures need checking for extra loading (as with most loft conversions), and whether retaining or underpinning calculations are required, as they are for basement conversions. Where structural work is part of a wider extension, loft or basement project, the structural calculation is typically bundled into the overall building regulations fee rather than charged again separately.
| Project scope | What's included | Fee guide |
|---|---|---|
| Single beam or wall removal | One steel calculation plus a drawing showing beam size, padstones and bearings | From £650 |
| Loft conversion structural package | Floor and roof loading checks, beam calculations, staircase opening design | Included within loft drawings from £1,100 |
| Rear or side extension structural package | Foundation design, steel beam calculations, roof loading checks | Included within planning and building regs packages from £2,200–£3,850 |
| Basement or retaining structure | Underpinning, retaining wall and waterproofing-adjacent structural calculations | Quoted individually — ground conditions vary |
Structural Drawings in Bexley Village DA5 — FAQs
Do I need a structural engineer to remove a wall in my London home?+
How long do structural calculations take?+
Will the steel beam on my drawings match what my builder orders?+
Can you produce structural drawings without handling my full planning application?+
Do structural calculations need to be submitted to Building Control?+
Do I need planning permission for an extension in Bexley?+
Can I build a bigger extension because Bexley plots are larger?+
What extra control applies in Old Bexley Village or around Danson Park?+
How long does Bexley Council take to decide?+
How much do planning drawings cost in Bexley?+
Get your free Bexley Village planning assessment
Tell us your Bexley Village (DA5) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.