Structural Drawings in Custom House E16
Fixed-fee, MCIAT-chartered structural drawings for Custom House (E16) homeowners — London Borough of Newham validation and local constraints handled from the start.
Custom House (E16) grew as Victorian dock-worker housing around the Royal Victoria Dock, which opened in 1855, and now sits inside the Royal Docks regeneration and Enterprise Zone. Surviving and postwar-rebuilt terraces sit alongside major new-build development around the ExCeL and the Elizabeth line, so householder work here is largely extensions and lofts on the terraced houses that line the residential streets.
There is no conservation area covering the Custom House part of E16 — that is a genuine, verified fact, not an omission. Its planning character is instead shaped by the working dockside terraced grain and the surrounding regeneration, and by the London Borough of Newham's householder design expectations, which lean on keeping original building lines, materials and roof continuity intact. We treat that terraced character, rather than a conservation designation, as the reference point when we design an extension.
Demand for rear extensions and loft conversions runs steadily across residential streets like Tollgate Road, Rogers Road and Chadwin Road, where compact terraced houses sit on modest plots. We check each property's permitted-development position against Newham's borough-wide controls first — and any surface-water drainage points given the low-lying dockside land — then prepare drawings that either stay within permitted development or are ready to validate as a full householder application.
Planning in Custom House (E16): what to know before you apply
Because Custom House is a dockside mix of surviving and rebuilt terraces set within the Royal Docks regeneration area, Newham assess extensions against the prevailing rhythm and building line of the individual residential street, so matching original brick, roof continuity and neighbour relationships matters alongside the numbers. There is no conservation area and no local Article 4 direction in the Custom House part of E16, so many terraced houses retain permitted development rights for rear and loft work — but compact plots, shared party walls and low-lying land mean depth, height, neighbour impact and drainage are the points a householder application is judged on.
Typical Custom House housing stock
A mix of surviving and postwar-rebuilt terraced housing with substantial new-build apartments across the Royal Docks regeneration area. It is the terraced houses on the residential streets, rather than the apartment blocks, that generate most of the rear-extension and loft-conversion work here.
Streets we regularly draw for in Custom House
Barrier Point Road · Tollgate Road · Rayleigh Road · Wesley Avenue · Rogers Road · Ruscoe Road · Egham Road · Chadwin Road · Cranley Road · Selby Road · Caraway Close · Eclipse Road
What E16 is actually built of
Measured from 274 classified residential buildings in E16, not from a description of the area.
Custom House E16 housing mix
Residential building form across the E16 postcode district, from 274 classified buildings.
| Attached on more than one side | 68% |
|---|---|
| Attached on one side | 27% |
| Detached | 4% |
| Median building footprint | 50 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 2.42 |
| Buildings classified | 274 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Structural Drawings for Custom House (E16) homes: the package and the process
Structural sheets are issued to be built from. Beam and lintel schedules give size, grade and bearing; connection details show how each element meets the next; and padstones, straps and restraint are drawn at the junctions rather than noted in general terms. Calculations are submitted alongside so Building Control can check the design rather than take it on trust.
Coordination with the architectural set is where the value is. A beam that is right in isolation but sits below the approved ceiling line, or a column that lands in a doorway, is a site problem that costs more to fix than it did to draw. We resolve those clashes in the drawing stage.
The existing structure sets the design. A terrace transfers load through party walls that are shared and often unrecorded, a semi through one; and floor construction — timber, concrete, or a mix from earlier alterations — changes how a new opening is supported and what has to be exposed to find out.
Do I need structural calculations to remove a load-bearing wall in London?
If a wall carries any load from above — a floor, a roof, another wall, or a chimney breast — you need a structural calculation before it can be removed, and Building Control will ask for it as part of a Full Plans or Building Notice submission. This covers the great majority of kitchen-diner knock-throughs in London terraces and semis, where the wall between the kitchen and the rear reception room is almost always load-bearing. A calculation confirms the size and type of steel beam needed to replace the wall's support, the padstones or pier that carry the beam's weight down to the foundations, and the temporary propping needed while the work is carried out. If the wall shares a boundary or the new beam bears on a party wall, the Party Wall etc. Act 1996 will also apply and needs to be dealt with separately from the calculation itself.
How steel beam sizing works
A structural engineer calculates the loads bearing down on a wall from the floors, roof and any walls above it, then sizes a steel beam (RSJ) — its depth, width and steel grade — so it can safely carry that load across the required span without excessive deflection. The calculation also fixes the bearing length at each end, the padstones or steel plates that spread the load into the surrounding masonry, and whether the existing foundations need strengthening to take the extra point loads. Because we coordinate the calculation with the architectural drawing set, the exact beam size, orientation and position shown on your plans is the one the calculation specifies — so your builder can order the correct steel first time, and Building Control sees a consistent set of drawings rather than two documents that disagree.
How much do structural drawings cost in London?
Structural drawings and calculations start from £650 for a single beam or wall removal, agreed as a fixed fee before work begins. The price depends on the number of beams or walls involved, whether foundations need designing from scratch (as with a rear or side extension), whether existing floor and roof structures need checking for extra loading (as with most loft conversions), and whether retaining or underpinning calculations are required, as they are for basement conversions. Where structural work is part of a wider extension, loft or basement project, the structural calculation is typically bundled into the overall building regulations fee rather than charged again separately.
| Project scope | What's included | Fee guide |
|---|---|---|
| Single beam or wall removal | One steel calculation plus a drawing showing beam size, padstones and bearings | From £650 |
| Loft conversion structural package | Floor and roof loading checks, beam calculations, staircase opening design | Included within loft drawings from £1,100 |
| Rear or side extension structural package | Foundation design, steel beam calculations, roof loading checks | Included within planning and building regs packages from £2,200–£3,850 |
| Basement or retaining structure | Underpinning, retaining wall and waterproofing-adjacent structural calculations | Quoted individually — ground conditions vary |
Structural Drawings in Custom House E16 — FAQs
Do I need a structural engineer to remove a wall in my London home?+
How long do structural calculations take?+
Will the steel beam on my drawings match what my builder orders?+
Can you produce structural drawings without handling my full planning application?+
Do structural calculations need to be submitted to Building Control?+
Do I need planning permission to extend a house in Custom House?+
Is Custom House in a conservation area?+
How much do planning and building-regulation drawings cost for a Custom House extension?+
How long does Newham Council take to decide?+
Get your free Custom House planning assessment
Tell us your Custom House (E16) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.