Side Return Extension Drawings in Becontree RM9
Fixed-fee, MCIAT-chartered side return extension drawings for Becontree (RM9) homeowners — London Borough of Barking and Dagenham validation and local constraints handled from the start.
Becontree (RM9) is defined by one thing above all: the Becontree Estate, built by the London County Council between 1921 and 1935 and still one of the largest public housing estates ever created, with roughly 26,000 homes laid out on garden-suburb principles. Almost every householder project here is an extension or loft on one of those cohesive interwar two-storey cottages, so the drawings have to sit comfortably within a very consistent, planned streetscape.
There is no conservation area covering Becontree — that is a genuine, verified fact, not an omission. Its planning character is instead shaped by the sheer uniformity of the estate layout and by the London Borough of Barking and Dagenham's design expectations, which lean on keeping the original cottage rhythm, materials and building lines intact. We treat that estate cohesion, rather than a conservation designation, as the reference point when we design an extension.
Because so many Becontree houses passed into private ownership after Right to Buy, demand for rear extensions, side infills and loft conversions is steady across streets like Gale Street, Lodge Avenue and Fitzstephen Road. We check each property's permitted-development position against Barking and Dagenham's borough-wide controls first, then prepare drawings that either stay within permitted development or are ready to validate as a full householder application.
Planning in Becontree (RM9): what to know before you apply
Because the estate is so uniform, Barking and Dagenham assess extensions on Becontree cottages against the consistent interwar street pattern, so matching original brick, render and roof form matters more than on a mixed-typology road. There is no conservation area and no estate-specific Article 4 direction, so many houses retain permitted development rights for rear and loft work — but the modest original plots and shared building lines mean depth, height and neighbour impact are the points a householder application is judged on.
Typical Becontree housing stock
Two-storey interwar cottages — short terraced and semi-detached runs of brick and rendered houses set behind small front gardens on wide, uniformly planned streets. Built by the London County Council between 1921 and 1935, many are now privately owned following Right to Buy, which is what drives the steady flow of rear-extension and loft-conversion work across the estate.
Streets we regularly draw for in Becontree
Lodge Avenue · Gale Street · Marlborough Road · Fitzstephen Road · Ilchester Road · Rutland Gardens · Babington Road · Dronfield Gardens · Hewett Road · Cornworthy Road · Harrold Road · Easebourne Road
What RM9 is actually built of
Measured from 248 classified residential buildings in RM9, not from a description of the area.
Becontree RM9 housing mix
Residential building form across the RM9 postcode district, from 248 classified buildings.
| Attached on more than one side | 62% |
|---|---|
| Attached on one side | 37% |
| Detached | 1% |
| Median building footprint | 48 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.06 |
| Buildings classified | 248 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Side Return Extension Drawings for Becontree (RM9) homes: the package and the process
A side return is a structural drawing as much as a planning one. Removing the original flank wall to open the kitchen into the infill needs a beam and a padstone detail, and the new roof has to be drawn where it meets both the existing rear elevation and the boundary wall.
The boundary is the sensitive line. The drawings set out where the new wall sits relative to it, how the roof drains without discharging next door, and where rooflights fall so the officer can see the room is lit without overlooking. That detail is also what your party wall surveyor will ask for.
The extension only exists where the alley does. Mid-terrace and end-of-terrace houses with a rear outrigger are the classic case; a semi with a flank path is a different scheme with different boundary questions; and a detached house has no side return to infill at all.
Do I need planning permission for a side return extension in London?
Permitted development rights for side extensions are narrower than for rear extensions: they generally cap the extension at a single storey, restrict its width to no more than half the width of the original house, and limit its height. In practice, a full-depth side return running the length of a Victorian or Edwardian terrace usually exceeds one or more of these limits, so most side return projects are drawn and submitted as a full householder planning application.
Conservation area status and Article 4 directions, common across inner London terraces, remove permitted development rights for side extensions entirely in many streets, reinforcing the need for a planning application. We check your property's status before drawing.
What does a side return extension involve?
A side return infills the alley at ground floor level, structurally opening the original flank wall of the kitchen into the new space so the two areas read as one room. Unlike a rear extension, which is bounded on three sides by your own garden, a side return is bounded on one long side by the neighbouring property, which shapes almost every decision in the design, from where the roof glazing sits to how deep the new foundations need to go.
- New flank wall built out to align with the rear of the house, following the boundary line
- Original external wall between kitchen and alley opened up and supported on a steel or glulam beam
- Roof over the new space either glazed in full, glazed in a strip along the boundary for a 'light well' effect, or pitched and tiled to match the main roof
- Kitchen re-planned across the combined footprint, often incorporating an island once the room widens
Will I need a Party Wall Agreement for a side return extension?
Almost certainly. Because the new side wall is built on or immediately against the boundary with the neighbouring property, the Party Wall etc. Act 1996 applies, and your neighbour must be formally notified before work starts. We prepare the drawings and dimensions your Party Wall surveyor needs, and time the notice period so it runs alongside, rather than after, your planning application.
| Package | What it covers | Typical fee |
|---|---|---|
| Side return, planning only | Full householder planning application drawings for the infill | Full Planning pack ~£1,600–£2,400 |
| Side return, planning + Building Regulations | Adds structural calculations, Party Wall drawings and construction detail | Planning + Building Regs pack ~£2,200–£3,850 |
| Side return + rear extension (wraparound) | Combines both extensions into one L-shaped ground floor | see Wraparound Extension Drawings |
| Measured survey only | A measured existing floor-plan set for your own architect, surveyor or builder | from £450 |
Side Return Extension Drawings in Becontree RM9 — FAQs
How much does a side return extension cost to design in London?+
Can I build a side return under permitted development?+
When do I need to serve Party Wall notice on my neighbour?+
Do I need an architect for a side return extension?+
How long does a side return extension take to design and approve?+
Do I need planning permission to extend a house on the Becontree Estate?+
Is Becontree in a conservation area?+
How much do planning and building-regulation drawings cost for a Becontree extension?+
How long does Barking & Dagenham Council take to decide?+
Get your free Becontree planning assessment
Tell us your Becontree (RM9) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.