Structural Drawings in Nunhead SE15
Fixed-fee, MCIAT-chartered structural drawings for Nunhead (SE15) homeowners — London Borough of Southwark validation and local constraints handled from the start.
Nunhead (SE15) is a largely Victorian terraced neighbourhood on the rising ground between Nunhead Cemetery and Peckham Rye, and as the area has gentrified the demand has shifted firmly toward side-return, rear and loft extensions on family houses. Because so many properties share the same terraced footprint, Southwark's design expectations for extension depth and dormers here are well established.
Conservation pockets around Nunhead Cemetery, Nunhead Green and Telegraph Hill bring tighter control over roof form, materials and frontages than the surrounding streets carry. We check where a Nunhead property sits relative to those boundaries before recommending a permitted-development or full-application route, and draw the scheme to Southwark's residential guidance so it is assessed cleanly.
Planning in Nunhead (SE15): what to know before you apply
SE15 has no published householder Article 4 direction affecting typical Nunhead work, so many houses retain permitted development rights for rear and loft projects — but the conservation pockets around Nunhead Cemetery, Nunhead Green and Telegraph Hill are the exceptions where roof and frontage changes are more closely controlled.
Typical Nunhead housing stock
Victorian and Edwardian terraces on the streets rising between Nunhead Cemetery and Peckham Rye, largely two-storey family houses with rear gardens, plus a share of houses converted into flats.
Streets we regularly draw for in Nunhead
Solway Road · Kinsale Road · Dovedale Road · Mundania Road
What SE15 is actually built of
Measured from 458 classified residential buildings in SE15, not from a description of the area.
Nunhead SE15 housing mix
Residential building form across the SE15 postcode district, from 458 classified buildings.
| Attached on more than one side | 71% |
|---|---|
| Attached on one side | 26% |
| Detached | 3% |
| Median building footprint | 61 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 2.15 |
| Buildings classified | 458 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Structural Drawings for Nunhead (SE15) homes: the package and the process
Structural sheets are issued to be built from. Beam and lintel schedules give size, grade and bearing; connection details show how each element meets the next; and padstones, straps and restraint are drawn at the junctions rather than noted in general terms. Calculations are submitted alongside so Building Control can check the design rather than take it on trust.
Coordination with the architectural set is where the value is. A beam that is right in isolation but sits below the approved ceiling line, or a column that lands in a doorway, is a site problem that costs more to fix than it did to draw. We resolve those clashes in the drawing stage.
The existing structure sets the design. A terrace transfers load through party walls that are shared and often unrecorded, a semi through one; and floor construction — timber, concrete, or a mix from earlier alterations — changes how a new opening is supported and what has to be exposed to find out.
Do I need structural calculations to remove a load-bearing wall in London?
If a wall carries any load from above — a floor, a roof, another wall, or a chimney breast — you need a structural calculation before it can be removed, and Building Control will ask for it as part of a Full Plans or Building Notice submission. This covers the great majority of kitchen-diner knock-throughs in London terraces and semis, where the wall between the kitchen and the rear reception room is almost always load-bearing. A calculation confirms the size and type of steel beam needed to replace the wall's support, the padstones or pier that carry the beam's weight down to the foundations, and the temporary propping needed while the work is carried out. If the wall shares a boundary or the new beam bears on a party wall, the Party Wall etc. Act 1996 will also apply and needs to be dealt with separately from the calculation itself.
How steel beam sizing works
A structural engineer calculates the loads bearing down on a wall from the floors, roof and any walls above it, then sizes a steel beam (RSJ) — its depth, width and steel grade — so it can safely carry that load across the required span without excessive deflection. The calculation also fixes the bearing length at each end, the padstones or steel plates that spread the load into the surrounding masonry, and whether the existing foundations need strengthening to take the extra point loads. Because we coordinate the calculation with the architectural drawing set, the exact beam size, orientation and position shown on your plans is the one the calculation specifies — so your builder can order the correct steel first time, and Building Control sees a consistent set of drawings rather than two documents that disagree.
How much do structural drawings cost in London?
Structural drawings and calculations start from £650 for a single beam or wall removal, agreed as a fixed fee before work begins. The price depends on the number of beams or walls involved, whether foundations need designing from scratch (as with a rear or side extension), whether existing floor and roof structures need checking for extra loading (as with most loft conversions), and whether retaining or underpinning calculations are required, as they are for basement conversions. Where structural work is part of a wider extension, loft or basement project, the structural calculation is typically bundled into the overall building regulations fee rather than charged again separately.
| Project scope | What's included | Fee guide |
|---|---|---|
| Single beam or wall removal | One steel calculation plus a drawing showing beam size, padstones and bearings | From £650 |
| Loft conversion structural package | Floor and roof loading checks, beam calculations, staircase opening design | Included within loft drawings from £1,100 |
| Rear or side extension structural package | Foundation design, steel beam calculations, roof loading checks | Included within planning and building regs packages from £2,200–£3,850 |
| Basement or retaining structure | Underpinning, retaining wall and waterproofing-adjacent structural calculations | Quoted individually — ground conditions vary |
Structural Drawings in Nunhead SE15 — FAQs
Do I need a structural engineer to remove a wall in my London home?+
How long do structural calculations take?+
Will the steel beam on my drawings match what my builder orders?+
Can you produce structural drawings without handling my full planning application?+
Do structural calculations need to be submitted to Building Control?+
Do I need planning permission for an extension in Southwark?+
What is the Dulwich Estate scheme of management?+
Can you handle a warehouse or riverside conversion in Bermondsey or Bankside?+
How long does Southwark Council take to decide?+
How much do planning drawings cost in Southwark?+
Get your free Nunhead planning assessment
Tell us your Nunhead (SE15) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.