Structural Drawings in Eltham SE9
Fixed-fee, MCIAT-chartered structural drawings for Eltham (SE9) homeowners — Royal Borough of Greenwich validation and local constraints handled from the start.
Eltham (SE9) sits in the Royal Borough of Greenwich and is best known for the Progress Estate at Well Hall — a 1915 Arts-and-Crafts garden suburb that inspired much interwar housing and has been a conservation area since 1971. An Article 4 direction covers the estate, so on those streets even small external changes need consent, and rear and loft projects have to be handled with real care for the original detailing.
Away from the estate, much of Eltham is consistent interwar semi-detached and terraced housing where side-return, rear and loft projects are the staple. The district also carries the setting of Eltham Palace and its listed gardens. We check where an Eltham property sits relative to the Progress Estate Article 4 area and the palace setting before recommending a permitted-development or full-application route under Greenwich's guidance.
Planning in Eltham (SE9): what to know before you apply
Eltham's Progress Estate at Well Hall carries a conservation-area designation and an Article 4 direction (1973), so permitted-development rights are removed across the estate and external changes need planning permission. Elsewhere in SE9 many interwar houses retain PD rights for rear and loft work, but the consistent frontages and the setting of Grade I listed Eltham Palace mean elevation and roof changes are assessed closely. We confirm which controls apply to a specific address before drawing.
Typical Eltham housing stock
The 1915 Arts-and-Crafts cottages and greens of the Progress Estate around Well Hall Road, interwar semi-detached and terraced housing across much of Eltham, and later post-war housing toward Mottingham and New Eltham.
Streets we regularly draw for in Eltham
Well Hall Road · Court Road · Eltham High Street · Ross Way
What SE9 is actually built of
Measured from 511 classified residential buildings in SE9, not from a description of the area.
Eltham SE9 housing mix
Residential building form across the SE9 postcode district, from 511 classified buildings.
| Attached on more than one side | 39% |
|---|---|
| Attached on one side | 57% |
| Detached | 4% |
| Median building footprint | 62 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.22 |
| Buildings classified | 511 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Structural Drawings for Eltham (SE9) homes: the package and the process
Structural sheets are issued to be built from. Beam and lintel schedules give size, grade and bearing; connection details show how each element meets the next; and padstones, straps and restraint are drawn at the junctions rather than noted in general terms. Calculations are submitted alongside so Building Control can check the design rather than take it on trust.
Coordination with the architectural set is where the value is. A beam that is right in isolation but sits below the approved ceiling line, or a column that lands in a doorway, is a site problem that costs more to fix than it did to draw. We resolve those clashes in the drawing stage.
The existing structure sets the design. A terrace transfers load through party walls that are shared and often unrecorded, a semi through one; and floor construction — timber, concrete, or a mix from earlier alterations — changes how a new opening is supported and what has to be exposed to find out.
Do I need structural calculations to remove a load-bearing wall in London?
If a wall carries any load from above — a floor, a roof, another wall, or a chimney breast — you need a structural calculation before it can be removed, and Building Control will ask for it as part of a Full Plans or Building Notice submission. This covers the great majority of kitchen-diner knock-throughs in London terraces and semis, where the wall between the kitchen and the rear reception room is almost always load-bearing. A calculation confirms the size and type of steel beam needed to replace the wall's support, the padstones or pier that carry the beam's weight down to the foundations, and the temporary propping needed while the work is carried out. If the wall shares a boundary or the new beam bears on a party wall, the Party Wall etc. Act 1996 will also apply and needs to be dealt with separately from the calculation itself.
How steel beam sizing works
A structural engineer calculates the loads bearing down on a wall from the floors, roof and any walls above it, then sizes a steel beam (RSJ) — its depth, width and steel grade — so it can safely carry that load across the required span without excessive deflection. The calculation also fixes the bearing length at each end, the padstones or steel plates that spread the load into the surrounding masonry, and whether the existing foundations need strengthening to take the extra point loads. Because we coordinate the calculation with the architectural drawing set, the exact beam size, orientation and position shown on your plans is the one the calculation specifies — so your builder can order the correct steel first time, and Building Control sees a consistent set of drawings rather than two documents that disagree.
How much do structural drawings cost in London?
Structural drawings and calculations start from £650 for a single beam or wall removal, agreed as a fixed fee before work begins. The price depends on the number of beams or walls involved, whether foundations need designing from scratch (as with a rear or side extension), whether existing floor and roof structures need checking for extra loading (as with most loft conversions), and whether retaining or underpinning calculations are required, as they are for basement conversions. Where structural work is part of a wider extension, loft or basement project, the structural calculation is typically bundled into the overall building regulations fee rather than charged again separately.
| Project scope | What's included | Fee guide |
|---|---|---|
| Single beam or wall removal | One steel calculation plus a drawing showing beam size, padstones and bearings | From £650 |
| Loft conversion structural package | Floor and roof loading checks, beam calculations, staircase opening design | Included within loft drawings from £1,100 |
| Rear or side extension structural package | Foundation design, steel beam calculations, roof loading checks | Included within planning and building regs packages from £2,200–£3,850 |
| Basement or retaining structure | Underpinning, retaining wall and waterproofing-adjacent structural calculations | Quoted individually — ground conditions vary |
Structural Drawings in Eltham SE9 — FAQs
Do I need a structural engineer to remove a wall in my London home?+
How long do structural calculations take?+
Will the steel beam on my drawings match what my builder orders?+
Can you produce structural drawings without handling my full planning application?+
Do structural calculations need to be submitted to Building Control?+
Do I need planning permission for an extension in Greenwich?+
How does the Maritime Greenwich World Heritage Site affect my project?+
Can I extend a home in Blackheath or Westcombe Park?+
How long does the Royal Borough of Greenwich take to decide?+
How much do planning drawings cost in Greenwich?+
Get your free Eltham planning assessment
Tell us your Eltham (SE9) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.