Structural Drawings in East Dulwich SE22
Fixed-fee, MCIAT-chartered structural drawings for East Dulwich (SE22) homeowners — London Borough of Southwark validation and local constraints handled from the start.
East Dulwich (SE22) sits in the London Borough of Southwark, tucked between Dulwich Village, Peckham and Forest Hill. Its character comes from the tight grid of late-Victorian and Edwardian terraces — the 'Derbyshire colony' of streets off Lordship Lane, including Melbourne Grove, built in the 1870s and 1880s. Rear, side-return and loft projects on these consistent terraces are the staple here.
The Gardens conservation area lies to the north-east, off East Dulwich Road by Peckham Rye Common, and the Dulwich Village conservation area borders the district to the south, so properties near either boundary answer to heightened design scrutiny. Southwark publishes its Article 4 directions and none covers these householder streets, so many East Dulwich houses keep permitted-development rights — we confirm where an address sits relative to the conservation areas before advising.
Planning in East Dulwich (SE22): what to know before you apply
Southwark publishes its Article 4 directions and none covers the East Dulwich householder streets, so many houses retain permitted-development rights for rear and loft work. The Gardens conservation area to the north-east and the Dulwich Village conservation area to the south are the controls that matter near those boundaries, and the consistent Victorian and Edwardian terrace frontages mean dormers and elevation changes are judged against the established grain. We check an address against those designations before drawing.
Typical East Dulwich housing stock
Late-Victorian and Edwardian terraces across the 'Derbyshire colony' streets off Lordship Lane — including Melbourne Grove — with grander villas toward Dulwich Village and the houses fronting Peckham Rye.
Streets we regularly draw for in East Dulwich
Lordship Lane · Melbourne Grove · North Cross Road · Barry Road
What SE22 is actually built of
Measured from 359 classified residential buildings in SE22, not from a description of the area.
East Dulwich SE22 housing mix
Residential building form across the SE22 postcode district, from 359 classified buildings.
| Attached on more than one side | 54% |
|---|---|
| Attached on one side | 40% |
| Detached | 6% |
| Median building footprint | 66 m² |
| Addresses per buildingAbove about 2 means flats and maisonettes dominate | 1.6 |
| Buildings classified | 359 |
Source: Ordnance Survey National Geographic Database (derived statistics). Contains OS data © Crown copyright and database right 2026. Contains Royal Mail data © Royal Mail copyright and database right 2026. Extracted 2026-08-17.
Structural Drawings for East Dulwich (SE22) homes: the package and the process
Structural sheets are issued to be built from. Beam and lintel schedules give size, grade and bearing; connection details show how each element meets the next; and padstones, straps and restraint are drawn at the junctions rather than noted in general terms. Calculations are submitted alongside so Building Control can check the design rather than take it on trust.
Coordination with the architectural set is where the value is. A beam that is right in isolation but sits below the approved ceiling line, or a column that lands in a doorway, is a site problem that costs more to fix than it did to draw. We resolve those clashes in the drawing stage.
The existing structure sets the design. A terrace transfers load through party walls that are shared and often unrecorded, a semi through one; and floor construction — timber, concrete, or a mix from earlier alterations — changes how a new opening is supported and what has to be exposed to find out.
Do I need structural calculations to remove a load-bearing wall in London?
If a wall carries any load from above — a floor, a roof, another wall, or a chimney breast — you need a structural calculation before it can be removed, and Building Control will ask for it as part of a Full Plans or Building Notice submission. This covers the great majority of kitchen-diner knock-throughs in London terraces and semis, where the wall between the kitchen and the rear reception room is almost always load-bearing. A calculation confirms the size and type of steel beam needed to replace the wall's support, the padstones or pier that carry the beam's weight down to the foundations, and the temporary propping needed while the work is carried out. If the wall shares a boundary or the new beam bears on a party wall, the Party Wall etc. Act 1996 will also apply and needs to be dealt with separately from the calculation itself.
How steel beam sizing works
A structural engineer calculates the loads bearing down on a wall from the floors, roof and any walls above it, then sizes a steel beam (RSJ) — its depth, width and steel grade — so it can safely carry that load across the required span without excessive deflection. The calculation also fixes the bearing length at each end, the padstones or steel plates that spread the load into the surrounding masonry, and whether the existing foundations need strengthening to take the extra point loads. Because we coordinate the calculation with the architectural drawing set, the exact beam size, orientation and position shown on your plans is the one the calculation specifies — so your builder can order the correct steel first time, and Building Control sees a consistent set of drawings rather than two documents that disagree.
How much do structural drawings cost in London?
Structural drawings and calculations start from £650 for a single beam or wall removal, agreed as a fixed fee before work begins. The price depends on the number of beams or walls involved, whether foundations need designing from scratch (as with a rear or side extension), whether existing floor and roof structures need checking for extra loading (as with most loft conversions), and whether retaining or underpinning calculations are required, as they are for basement conversions. Where structural work is part of a wider extension, loft or basement project, the structural calculation is typically bundled into the overall building regulations fee rather than charged again separately.
| Project scope | What's included | Fee guide |
|---|---|---|
| Single beam or wall removal | One steel calculation plus a drawing showing beam size, padstones and bearings | From £650 |
| Loft conversion structural package | Floor and roof loading checks, beam calculations, staircase opening design | Included within loft drawings from £1,100 |
| Rear or side extension structural package | Foundation design, steel beam calculations, roof loading checks | Included within planning and building regs packages from £2,200–£3,850 |
| Basement or retaining structure | Underpinning, retaining wall and waterproofing-adjacent structural calculations | Quoted individually — ground conditions vary |
Structural Drawings in East Dulwich SE22 — FAQs
Do I need a structural engineer to remove a wall in my London home?+
How long do structural calculations take?+
Will the steel beam on my drawings match what my builder orders?+
Can you produce structural drawings without handling my full planning application?+
Do structural calculations need to be submitted to Building Control?+
Do I need planning permission for an extension in Southwark?+
What is the Dulwich Estate scheme of management?+
Can you handle a warehouse or riverside conversion in Bermondsey or Bankside?+
How long does Southwark Council take to decide?+
How much do planning drawings cost in Southwark?+
Get your free East Dulwich planning assessment
Tell us your East Dulwich (SE22) address and ambition — we'll confirm feasibility, local constraints and a fixed fee within one working day.